Skip to content

Your repair explained, then a check-in call later on: (559) 576-5577

(559) 576-5577

ServicesPaint and Refinishing

Paint and Refinishing in Selma

We refinish damaged, faded and peeling paint so the panel matches the rest of your car in daylight, not just under shop lights. Every job gets careful prep, a blended color match and a clear coat, and we check in once you are back on the road.

Painter in a dark T-shirt sprays red paint on a car's rear quarter panel, with the rest of the car masked in paper and tape inside a lit paint booth

What paint and refinishing covers

Factory paint is a thin system: primer, a colored basecoat and a clear coat on top that takes most of the weather. When the clear fails, the color underneath oxidizes, chalks and eventually flakes. Scratches that reach primer, chips that start to rust and panels replaced in a collision repair all need the same thing: the layers rebuilt properly, in the right order.

Some cars only need one panel refinished and blended into its neighbors. Others have clear coat failing across the roof, hood and trunk, where a larger refinish makes more sense than chasing spots. We look at the whole car, tell you which one you have, and explain why.

The finish is only part of the job. Fresh paint stays soft for several weeks once it leaves the shop, so we walk you through washing and waxing timing at pickup, then follow up to make sure it is curing the way it should.

What the work includes

Surface prep down to sound material
We sand out failed clear, feather chipped edges and treat any rust before primer goes on. Paint laid over a weak layer lifts later, so this step gets the most time.
Color matching by sample, not by code alone
Your paint code is a starting point. Factory color varies by batch and sun exposure, so we spray test cards and compare them to your car before painting the panel.
Blending into adjacent panels
When a door is refinished, we usually fade the new color into the fender or quarter panel beside it. That keeps the eye from catching a hard line where old meets new.
Clear coat and finish work
A full clear coat goes over the color for gloss and UV protection. Once it cures, we wet sand and polish out any texture or dust so the surface reflects cleanly.
Masking and protection
Glass, trim, rubber seals and the interior are covered while we work. Parts that mask poorly, like some emblems and moldings, are removed and refitted instead.

Signs your car needs refinishing

  • Clear coat peeling or looking cloudy

    White, hazy patches on the roof or hood mean the clear is breaking down. Once it starts to peel, polishing will not bring it back.

  • Chips that have started to rust

    Small stone chips on the hood or rocker panels can let moisture reach bare metal. Catching them before rust spreads keeps the repair small.

  • Faded or chalky color

    Long summers of strong sun bake horizontal panels first. If a cloth picks up color when you rub the paint, the surface is oxidizing.

  • A panel that does not match

    A previous repair can look fine in the shade and wrong in sunlight. Mismatched shade or metallic flake is something we can correct.

  • Scratches you can catch with a fingernail

    If a scratch snags your nail, it has gone through the clear and needs to be filled and refinished, not just buffed.

How a paint job runs at our shop

  1. 1

    Look at the car together

    You bring your vehicle in and we inspect the paint in good light, measure film where it helps and show you what we see. You get a written estimate that lists the panels and the steps.

  2. 2

    Prep and prime

    We remove trim where needed, sand, repair any small dents or rust, then prime and block the surface flat. Most of the hours on a quality paint job are spent here.

  3. 3

    Match, spray and clear

    Test cards confirm the color before it touches your car. Basecoat and clear go on in a clean spray environment, then the finish is allowed to cure.

  4. 4

    Polish, reassemble and inspect

    We correct any texture, refit trim and look the car over outdoors in natural light. You leave with care instructions in hand, and we check in with you a few weeks on.

Damaged gray pickup with a crushed front end on a flatbed tow truck outside an auto body shop's open bays as two workers look it over

Where the price of a refinish comes from

Most of a refinish estimate is labor: the prep hours and the steps a particular color needs. The material itself is a smaller share. We price each job once we have seen the car in person, and the written estimate lists panels and steps so you can see where the time goes.

How much area needs paint
A single bumper corner is a different job from a hood, roof and trunk with failing clear. Blending into neighboring panels adds area but gives a better match.
Condition under the paint
Rust, old filler or a previous repair that was done poorly all have to be corrected before new paint goes on.
Color and finish type
Solid colors are simplest. Metallics, pearls and tri-coat whites take more steps to match and more material to apply.
Trim and parts removal
Cars with many moldings, sensors or emblems take longer to disassemble and refit, which is the right way to avoid tape lines.

Paint and refinishing questions

Something not covered here? (559) 576-5577

Is the paint work covered by a warranty?

Yes. Every refinish we do carries a lifetime warranty on all paint work. If something in the finish we applied is not right, bring your car back and we will look at it.

How close will the color be to my original paint?

Close enough that you should not be able to pick out the panel. We start with the factory code, then spray sample cards and hold them against your car in daylight. On most jobs we also blend into the neighboring panels, which covers the slight shift that years of sun put into original paint.

How soon can I wash or wax my car once I have it back?

Gentle hand washing is usually fine soon, but skip automatic car washes and wax for a while so the clear can finish curing. We give you specific timing for your job at pickup and go over it again when we check in.

Can you just touch up a few chips instead of painting the whole panel?

Sometimes, yes. Small chips on a hood can be filled and leveled without a full refinish. If the clear around them is already failing, we will tell you plainly that a touch-up would not last.

Do you handle paint as part of an insurance repair?

We do. When paint follows collision repair or bumper repair, it is part of the same estimate, and our Insurance Claims page explains how we work with your insurer.

Bring your paint questions to us

Describe the chips, fading or mismatch over the phone and we will walk through the realistic options before you drive in. Drivers come from Selma, Kingsburg, Fowler and nearby towns for refinishing.